General Regulations
- EN 12312-4: Aircraft ground equipment. Specific requirements. Part 4: Passenger boarding gate bridges.
- ADA: American with Disabilities Act. “ADA Standards for Accessible Design”.
- EN 6349-8: Maritime Structures. Part 8: Code of practice for the design of Ro-Ro ramps, link spans and walkways.
- EN 81-70:2003. Safety regulations for the construction and installation of elevators. Special applications to passenger elevators and of passengers and cargo. Part 70: Accessibility to lifts for persons including persons with disabilities.
Environmental impact evaluation
- Royal Legislative Decree 1/2008, January 11, approving the revised text of the Law on Environmental Impact Evaluation of projects.
- Act 11/2006 of 14 September, environmental impact evaluations and strategic environmental evaluations in Autonomous Community of Andalusia.
Occupational Safety and Health
- Act 31/1995 of 8 November Prevention Occupational Risks.
- Act 54/2003 of 12 December on regulatory reform of the prevention of occupational hazards.
- Royal Legislative Decree 486/1997 of 14 April, the minimum healthcare and safety requirements set out in the workplace.
- Royal Legislative Decree 1627/1997, of 24 October laying minimum requirements for safety and health requirements laid down in construction activities
- Royal Legislative Decree 14/2001 of 8 June on minimum standards for the protection of the health and security of any employees against the electrical risk.
- Decree 72/1992 of May 5, where the technical standards for accessibility and removal of architectural, urban and transport barriers in Andalucia are approved,
- RD1544/2007 of 23 November, where are regulated the basic conditions of accessibility and non-discrimination for access and use of transport for people with disabilities and Technical Building Code.
- PTN: Prevention Technical Norms
Materials structures and welding.
• UNE EN 10025. Heat laminated rolled products of structural steels.
• UNE EN 1011. Welding. Recommendations for welding of metallic materials.
• UNE EN 15614-1. Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 1: Arc and gas welding of steels and arc nickel and its alloys.
• UNE EN 287-1. Qualification of welders. Fusion welding. Part 1: Steels.
• UNE EN 571-1. Non-destructive testing. Liquid penetrant Test. Part 1: General principles.
• UNE EN 23277. Non-destructive test of welded unions. Testing of welded joints using penetrating liquids. Acceptance levels.
• UNE EN 970. Non-destructive examination of fusion welds. visual examination
• UNE EN 13018. Non-destructive testing. Visual inspection. General principles.
• UNE EN 5817. Welding. Fusion welded unions of steel, nickel, titanium and their alloys. Quality levels for imperfections
• UNE EN 473. Non-destructive testing. Qualification and certification of personnel performing non-destructive testing. General principles.
• Standards CEN / TC 274. Aircraft ground support equipment
Prosertek also meets the following standards in their production processes:
• CTE-SE. Technical Code for Construction. Structural safety.
- CTE-SE-A. Technical Building Code. Steel.
- EN 1991-1-4. Eurocode 1. Part 1.4. Actions on Structures. Shares of wind.
- NCSE-02. Standard seismic construction: General section and building.
- IAP-11. Instruction on the actions to be considered in the proposed road bridge (2011).
- EAE. Instructions of Structural Steel.
Mechanical Components
All electrical installation complies with the following directives:
- Electromagnetic Compatibility Directive 2004/108/EC.
- Low Voltage Directive 2006/95/EC
And with the standards of the International Electrotechnical Commission (IEC), including:
- IEC 114. Protection for low voltage applications,
- IEC 158. Applications of low voltage control,
- IEC 337. Auxiliary control
- IEC 445. Identification of equipment
- IEC 446. Color driver identification numerals,
- IEC 529. Classification of levels of protection provided by enclosures.
Hydraulic Components
- EN 853 / ISO 1436. Hydraulic hose with 2 spiral steel mesh
- EN 856/DIN 20023. Hydraulic hose with 4 spiral steel mesh
- ANSI B.31.3. Rigid pipe stainless
- BS 5200. Specification for dimensions of hydraulic connectors and adaptors
- DIN 2353. Non-soldering compression fittings with cutting ring – Complete fittings and survey.
- AISI 316. Material, Fittings, tubing, hydraulic hose end stainless steel.
- DIN 19704. Hydraulic steel structures. Part 1: Criteria for design and calculation
- CETOP Standards.
Rustproofing
- UNE EN ISO 1461. Heat dip galvanized coatings on fabricated ferrous. Specifications and test methods / corrosion protection.
Other regulations
- ROM 2.0-11 Recommendations for the design and execution of works docking and mooring